AXIS M4308-PLE Panoramic Camera

Preview mode is ideal for installers when fine tuning the camera view during the installation. No login is required to access the camera view in preview mode. It is available only in factory defaulted state for a limited time from powering up the device.

To find Axis devices on the network and assign them IP addresses in Windows®, use AXIS IP Utility or AXIS Device Manager. Both applications are free and can be downloaded from axis.com/support.

For more information about how to find and assign IP addresses, go to How to assign an IP address and access your device.

You can use the device with the following browsers:

✓: Recommended
*: Supported with limitations

1. Open a browser and type the IP address or host name of the Axis device.

   If you don’t know the IP address, use AXIS IP Utility or AXIS Device Manager to find the device on the network.

2. Type the username and password. If you access the device for the first time, you must create an administrator account. See Create an administrator account.

For descriptions of all features and settings in the web interface of devices with AXIS OS, see AXIS OS web interface help.

1. To make sure that the device has its original AXIS OS, or to take full control of the device after a security attack:

2. Reset to factory default settings. See Reset to factory default settings.

   After the reset, secure boot guarantees the state of the device.

3. Configure and install the device.

The first time you log in to your device, you must create an administrator account.

1. Enter a username.

2. Enter a password. See Secure passwords.

3. Re-enter the password.

4. Accept the license agreement.

5. Click Add account.

The device password is the primary protection for your data and services. Axis devices do not impose a password policy as they may be used in various types of installations.

To protect your data we strongly recommend that you:

• Use a password with at least 8 characters, preferably created by a password generator.

• Don’t expose the password.

• Change the password at a recurring interval, at least once a year.

This video gives you an overview of the device’s web interface.

This section includes instructions about configuring your device. If you want to learn more about how certain features work, go to Learn more.

To rotate the 360° view, go to Video > Installation and use the Roll slider.

You can also enter a value for the roll angle in the text field.

1. Click and select Legacy device interface.

2. Select Quad view among the live feed sources.

3. Go to Settings > System > Orientation and click .

4. To change the view order, drag and drop the yellow boxes.

Capture mode sets the boundaries of the video image, affecting how the image is captured and processed. Beyond aspect ratio and resolution, it affects many other settings as well, such as, exposure zones, guard tours, image overlays, motion detection (include areas and exclude areas), preset positions, privacy masks, and view areas. The following capture modes are available:

View	Video image boundaries
Overview
Panorama
Double Panorama
Quad View
View Areas 1-4
Corner Left/Right
Double Corner
Corridor

• Which capture mode to choose depends on the requirements of frame rate and resolution for the specific surveillance setup. For specifications about available capture modes, see the product’s datasheet. To find the latest version of the datasheet, go to axis.com.

1. To adjust the view in relation to a reference area or object, use the leveling guide in combination with the digital roll slider in the camera.

2. Go to Settings > System > Orientation and click .

3. Adjust the camera by using Digital roll until the position of the reference area or object, is aligned with the leveling guide.

To improve image quality for specific surveillance scenes, use exposure modes. Exposure modes lets you control aperture, shutter speed, and gain. Go to Video > Image > Exposure and select between the following exposure modes:

• For most use cases, select Automatic exposure.

• For environments with certain artificial lighting, for example fluorescent lighting, select Flicker-free.

  Select the same frequency as the power line frequency.

• For environments with certain artificial light and bright light, for example outdoors with fluorescent lighting at night and sun during daytime, select Flicker-reduced.

  Select the same frequency as the power line frequency.

• To lock the current exposure settings, select Hold current.

Depending on the installation environment and the conditions around the camera, for example external light sources in the scene, you can sometimes improve the image quality if you manually adjust the intensity of the LEDs. If you have problems with reflections from the LEDs, you can try to reduce the intensity.

1. Go to Video > Image > Day-night mode.

2. Turn on Allow illumination.

3. Click in the live view and select Manual.

4. Adjust the intensity.

Your camera uses visible light to deliver color images during the day. But as the visible light diminishes, color images become less bright and clear. If you switch to night mode when this happens, the camera uses both visible and near-infrared light to deliver bright and detailed black-and-white images instead. You can set the camera to switch to night mode automatically.

1. Go to Video > Image > Day-night mode, and make sure that the IR-cut filter is set to Auto.

To reduce noise in low-light conditions, you can adjust one or more of the following settings:

• Adjust the trade-off between noise and motion blur. Go to Settings > Image > Exposure and move the Blur-noise trade-off slider toward Low noise.

• Set the exposure mode to automatic.

• Note

  A high max shutter value can result in motion blur.

• To slow down the shutter speed, set max shutter to the highest possible value.

• Reduce sharpness in the image.

• To reduce motion blur in low-light conditions, adjust one or more of the following settings in Video > Image > Exposure:
• Note

  When you increase the gain, image noise also increases.

• Set Max shutter to a shorter time, and Max gain to a higher value.

• If you still have problems with motion blur:

• Increase the light level in the scene.

• Mount the camera so that objects move toward it or away from it rather than sideways.

• Go to Video > Stream > General and set the compression as low as possible.

• Below the live view image, click and in Video format, select MJPEG.

• Go to Video > Stream > Zipstream and select Off.

Dynamic range is the difference in light levels in an image. In some cases the difference between the darkest and the brightest areas can be significant. The result is often an image where either the dark or the bright areas are visible. Wide dynamic range (WDR) makes both dark and bright areas of the image visible.

1. Go to Video > Image > Wide dynamic range.

2. Turn on WDR.

3. If you still have problems, go to Exposure and adjust the Exposure zone to cover the area of interest.

Find out more about WDR and how to use it at axis.com/web-articles/wdr.

You can create one or several privacy masks to hide parts of the image.

1. Go to Video > Privacy masks.

2. Click .

3. Click the new mask and type a name.

4. Adjust the size and placement of the privacy mask according to your needs.

5. To change the color for all privacy masks, click Privacy masks and select a color.

See also Privacy masks

You can add an image as an overlay in the video stream.

1. Go to Video > Overlays.

2. Click Manage images.

3. Upload or drag and drop an image.

4. Click Upload.

5. Select Image from the drop-down list and click .

6. Select the image and a position. You can also drag the overlay image in the live view to change the position.

This example explains how to display the text “Motion detected” when the device detects an object.

1. Start the application if it is not already running.

2. Make sure you have set up the application according to your needs.

1. Add the overlay text:

2. Go to Video > Overlays.

3. Under Overlays, select Text and click .

4. Enter #D in the text field.

5. Choose text size and appearance.

6. To position the text overlay, click and select an option.

1. Create a rule:

2. Go to System > Events and add a rule.

3. Type a name for the rule.

4. In the list of actions, under Overlay text, select Use overlay text.

5. Select a video channel.

6. In Text, type “Motion detected”.

7. Set the duration.

8. Click Save.

If there are parts of the scene that you don’t want the camera to reach, you can limit the pan, tilt, and zoom movements. For example, you want to protect the privacy of residents in an apartment building, which is located close to a parking lot that you intend to monitor.

To limit the movements:

1. Go to PTZ > Limits.

2. Set the limits as needed.

A guard tour displays the video stream from different preset positions either in a predetermined or random order, and for configurable periods of time.

1. Go to PTZ > Guard tours.

2. Click Guard tour.

3. Select Preset position and click Create.

4. Under General settings:

5. • Enter a name for the guard tour and specify the pause length between each tour.

   • If you want the guard tour to go to the preset positions in a random order, turn on Play guard tour in random order.

6. Under Step settings:

7. • Set the duration for the preset.

   • Set the move speed, which controls how fast to move to the next preset.

8. Go to Preset positions.

9. 1. Select the preset positions that you want in your guard tour.

   2. Drag them to the View order area, and click Done.

10. To schedule the guard tour, go to System > Events.

This section includes instructions about configuring your device. To learn more about how streaming and storage works, go to Streaming and storage.

1. Go to Video > Stream.

2. Click in the live view.

3. Select Video format AV1 if your device supports it. Otherwise select H.264.

4. Go to Video > Stream > General and increase Compression.

5. Go to Video > Stream > Zipstream and do one or more of the following:

6. • Note

     The Zipstream settings are used for all video encodings except MJPEG.

   • Select the Zipstream Strength that you want to use.

   • Turn on Optimize for storage. This can only be used if the video management software supports B-frames.

   • Turn on Dynamic FPS.

   • Turn on Dynamic GOP and set a high Upper limit GOP length value.

1. To store recordings on the network, you need to set up your network storage.

2. Go to System > Storage.

3. Click Add network storage under Network storage.

4. Type the IP address of the host server.

5. Type the name of the shared location on the host server under Network share.

6. Type the username and password.

7. Select the SMB version or leave it on Auto.

8. Select Add share without testing if you experience temporary connection issues, or if the share is not yet configured.

9. Click Add.

1. Record video directly from the camera

2. Go to Video > Stream.

3. To start a recording, click .

   If you haven’t set up any storage, click and . For instructions on how to set up network storage, see Set up network storage

4. To stop recording, click again.

1. Watch video

2. Go to Recordings.

3. Click for your recording in the list.

You can create rules to make your device perform an action when certain events occur. A rule consists of conditions and actions. The conditions can be used to trigger the actions. For example, the device can start a recording or send an email when it detects motion, or show an overlay text while the device is recording.

To learn more, see Get started with rules for events.

1. Go to System > Events and add a rule. The rule defines when the device will perform certain actions. You can set up rules as scheduled, recurring, or manually triggered.

2. Enter a Name.

3. Select the Condition that must be met to trigger the action. If you specify more than one condition for the rule, all of the conditions must be met to trigger the action.

4. Select which Action to perform when the conditions are met.

This example explains how to set up the camera to start recording to the SD card when the camera detects an object. The recording will include five seconds before detection and one minute after detection ends.

Before you start:

• Make sure you have an SD card installed.

1. Start the application if it is not already running.

2. Make sure you have set up the application according to your needs.

1. Create a rule:

2. Go to System > Events and add a rule.

3. Type a name for the rule.

4. In the list of actions, under Recordings, select Record video while the rule is active.

5. In the list of storage options, select SD_DISK.

6. Select a camera and a stream profile.

7. Set the prebuffer time to 5 seconds.

8. Set the postbuffer time to 1 minute.

9. Click Save.

This example explains how to set up the camera to start recording to the SD card five seconds before it detects loud noise and to stop two minutes after.

1. Turn on audio:

2. Set up the stream profile to include audio, see Add audio to your recording.

1. Turn on audio detection:

2. Go to System > Detectors > Audio detection.

3. Adjust the sound level according to your needs.

1. Create a rule:

2. Go to System > Events and add a rule.

3. Type a name for the rule.

4. In the list of conditions, under Audio, select Audio Detection.

5. In the list of actions, under Recordings, select Record video.

6. In the list of storage options, select SD_DISK.

7. Select the stream profile where audio has been turned on.

8. Set the prebuffer time to 5 seconds.

9. Set the postbuffer time to 2 minutes.

10. Click Save.

You have the option to connect the AXIS I/O Indication LED to your network camera. This LED can be configured to turn on whenever certain events occur in the camera. For example, to let people know that video recording is in progress.

Required hardware

• AXIS I/O Indication LED

• An Axis network video camera

• Note

  AXIS I/O Indication LED should be connected to an output port.

• Note

  For instructions on how to connect the AXIS I/O Indication LED, see the installation guide provided with the product.

The following example shows how to configure a rule that turns on the AXIS I/O Indication LED to indicate that camera is recording.

1. Go to System > Accessories > I/O ports.

2. Make sure that the port you connected the AXIS I/O Indication LED to is set to Output. Set the normal state to Circuit open.

3. Go to System > Events.

4. Create a new rule.

5. Select the Condition that must be met to trigger the camera to start recording. It can, for example, be a time schedule or motion detection.

6. In the list of actions, select Record video. Select a storage space. Select a stream profile or create a new. Also set the Prebuffer and Postbuffer as required.

7. Save the rule.

8. Create a second rule and select the same Condition as in the first rule.

9. In the list of actions, select Toggle I/O while the rule is active, and then select the port the AXIS I/O Indication LED is connected to. Set the state to Active.

10. Save the rule.

• Other scenarios where AXIS I/O Indication LED can be used are for example:

• Configure the LED to turn on when the camera starts, to indicate the presence of the camera. Select System ready as a condition.

• Configure the LED to turn on when live stream is active to indicate that a person or a program is accessing a stream from the camera. Select Live stream accessed as a condition.

You need to connect the switch relay to the camera from the camera’s web interface. First, configure the I/O ports:

Set the PIR detector to an input port

1. Go to System > Accessories > I/O ports.

2. Click to set the direction to input for port 1.

3. Give the input module a descriptive name, for example “PIR detector”.

4. If you want to trigger an event whenever the PIR detector senses motion, click to set the normal state to circuit open.

Set the switch relay to an output port

1. Click to set the direction to output for port 2.

2. Give the output module a descriptive name, for example “Gate switch”.

3. If you want to open the gate whenever an event is triggered, click to set the normal state to circuit closed.

For the camera to open the gate when the PIR detector senses someone nearby, you need to create a rule in the camera:

1. Go to System > Events and add a rule.

2. Type a name for the rule, for example “Open gate”.

3. In the list of conditions, select PIR detector.

4. In the list of actions, select Toggle I/O once.

5. In the list of ports, select Gate switch.

6. Set state to Active.

7. Set the duration.

8. Click Save.

9. Create another rule with the name “Direct the camera to the gate".

10. Select the same input signal as before, but as action select the previously created “Gate entrance” preset position.

11. Click Save.

This example explains how to set up an email notification when the housing or casing of the device is opened.

1. Add an email recipient:

2. Go to System > Events > Recipients and click Add recipient.

3. Type a name for the recipient.

4. Select Email as the notification type.

5. Type the recipient’s email address.

6. Type the email address that you want the camera to send notifications from.

7. Provide the login details for the sending email account, along with the SMTP hostname and port number.

8. To test your email setup, click Test.

9. Click Save.

10. Create a rule:

11. Go to System > Events > Rules and click Add a rule.

12. Type a name for the rule.

13. In the list of conditions, select Casing open.

14. In the list of actions, select Send notification to email.

15. Select a recipient from the list.

16. Type a subject line and message for the email.

17. Click Save.

This example explains how to send an email when the input signal is cut or short-circuited. For more information about the I/O connector, see I/O connector.

1. Go to System > Accessories > I/O ports and turn on Supervised.

1. Add an email recipient:

2. Go to System > Events > Recipients and add a recipient.

3. Type a name for the recipient.

4. Select Email as the notification type.

5. Type the recipient’s email address.

6. Type the email address that you want the camera to send notifications from.

7. Provide the login details for the sending email account, along with the SMTP hostname and port number.

8. To test your email setup, click Test.

9. Click Save.

1. Create a rule:

2. Go to System > Events > Rules and add a rule.

3. Type a name for the rule.

4. In the list of conditions, under I/O, select Supervised input tampering is active.

5. Select the relevant port.

6. In the list of actions, under Notifications, select Send notification to email and then select the recipient from the list.

7. Type a subject line and message for the email.

8. Click Save.

This example explains how to set up an email notification when the camera lens gets either spray painted, covered, or blurred.

1. Activate the tampering detection:

2. Go to System > Detectors > Camera tampering.

3. Set a value for Trigger delay. The value indicates the time that must pass before an email is sent.

4. Turn on Trigger on dark images to detect if the lens is sprayed, covered, or rendered severely out of focus.

5. Add an email recipient:

6. Go to System > Events > Recipients and add a recipient.

7. Type a name for the recipient.

8. Select Email as the notification type.

9. Type the recipient’s email address.

10. Type the email address that you want the camera to send notifications from.

11. Provide the login details for the sending email account, along with the SMTP hostname and port number.

12. To test your email setup, click Test.

13. Click Save.

14. Create a rule:

15. Go to System > Events > Rules and add a rule.

16. Type a name for the rule.

17. In the list of conditions, under Video, select Tampering.

18. In the list of actions, under Notifications, select Send notification to email and then select the recipient from the list.

19. Type a subject line and message for the email.

20. Click Save.

1. Turn on audio:

2. Go to Video > Stream > Audio and include audio.

3. If the device has more than one input source, select the correct one in Source.

4. Go to Audio > Device settings and turn on the correct input source.

5. If you make any changes to the input source, click Apply changes.

6. Edit the stream profile that is used for the recording:

7. Go to System > Stream profiles and select the stream profile.

8. Select Include audio and turn it on.

9. Click Save.

Turn on Voice enhancement:

1. Go to Audio > Audio enhancement.

2. Turn on Voice enhancement.

To read about all the features and settings available in the web interface of devices with AXIS OS, go to AXIS OS web interface help.

A view area is a cropped part of the full view. You can stream and store view areas instead of the full view to minimize bandwidth and storage needs. If you enable PTZ for a view area, you can pan, tilt and zoom within it. By using view areas you can remove parts of the full view, for example, the sky.

What capture mode to choose depends on the requirements for the frame rate and resolution of the specific surveillance setup. For specifications about available capture modes, see the product’s datasheet at axis.com.

A privacy mask is a user-defined area that covers a part of the monitored area. In the video stream, privacy masks appear either as blocks of solid color or with a mosaic pattern.

You’ll see the privacy mask on all snapshots, recorded video, and live streams.

You can use the VAPIX® application programming interface (API) to hide the privacy masks.

You can create several privacy masks. Each mask can have 3 to 10 anchor points.

Overlays are superimposed over the video stream. They are used to provide extra information during recordings, such as a timestamp, or during product installation and configuration. You can add either text or an image.

A guard tour displays the video stream from different preset positions either in a predetermined or random order, and for configurable periods of time. Once started, a guard tour continues to run until stopped, even when there are no clients (web browsers) viewing the images.

Decide which compression method to use based on your viewing requirements, and on the properties of your network. The available options are:

Motion JPEG

Motion JPEG, or MJPEG, is a digital video sequence that is made up of a series of individual JPEG images. These images are then displayed and updated at a rate sufficient to create a stream that shows constantly updated motion. For the viewer to perceive motion video the rate must be at least 16 image frames per second. Full motion video is perceived at 30 (NTSC) or 25 (PAL) frames per second.

The Motion JPEG stream uses considerable amounts of bandwidth, but provides excellent image quality and access to every image contained in the stream.

H.264 or MPEG-4 Part 10/AVC

H.264 can, without compromising image quality, reduce the size of a digital video file by more than 80% compared to the Motion JPEG format and by as much as 50% compared to older MPEG formats. This means that less network bandwidth and storage space are required for a video file. Or seen another way, higher video quality can be achieved for a given bitrate.

H.265 or MPEG-H Part 2/HEVC

H.265 can, without compromising image quality, reduce the size of a digital video file by more than 25% compared to H.264.

The Image tab contains camera settings that affect all video streams from the product. If you change something in this tab, it immediately affects all video streams and recordings.

The Stream tab contains settings for video streams. You get these settings if you request a video stream from the product and don’t specify for example resolution, or frame rate. When you change the settings in the Stream tab, it doesn’t affect ongoing streams, but it will take effect when you start a new stream.

The Stream profiles settings override the settings from the Stream tab. If you request a stream with a specific stream profile, the stream contains the settings of that profile. If you request a stream without specifying a stream profile, or request a stream profile that doesn't exist in the product, the stream contains the settings from the Stream tab.

Bitrate control helps you to manage the bandwidth consumption of your video stream.

Variable bitrate (VBR)
Variable bitrate allows the bandwidth consumption to vary depending on the level of activity in the scene. The more activity, the more bandwidth you need. With variable bitrate you are guaranteed constant image quality, but you need to make sure you have storage margins.

Maximum bitrate (MBR)
Maximum bitrate lets you set a target bitrate to handle bitrate limitations in your system. You might see a decline in image quality or frame rate as the instantaneous bitrate is kept below the specified target bitrate. You can choose to prioritize either image quality or frame rate. We recommend that you configure the target bitrate to a higher value than the expected bitrate. This gives you a margin in case there is a high level of activity in the scene.

Average bitrate (ABR)
With average bitrate, the bitrate is automatically adjusted over a longer period of time. This is so you can meet the specified target and provide the best video quality based on your available storage. Bitrate is higher in scenes with a lot of activity, compared to static scenes. You are more likely to get better image quality when in scenes with a lot of activity if you use the average bitrate option. You can define the total storage required to store the video stream for a specified amount of time (retention time) when image quality is adjusted to meet the specified target bitrate. Specify the average bitrate settings in one of the following ways:

• To calculate the estimated storage need, set the target bitrate and the retention time.

• To calculate the average bitrate, based on available storage and required retention time, use the target bitrate calculator.

• 1. Target bitrate
  2. Actual average bitrate
• You can also turn on maximum bitrate and specify a target bitrate within the average bitrate option.
• 1. Target bitrate
  2. Actual average bitrate

With analytics and apps you can get more out of your Axis device. AXIS Camera Application Platform (ACAP) is an open platform that makes it possible for third parties to develop analytics and other apps for Axis devices. Apps can be preinstalled on the device, available for download for free, or for a license fee.

To find the user manuals for Axis analytics and apps, go to help.axis.com.

AXIS People Counter is an analytic application that you can install on a network camera. You can use the application to count how many people pass through an entrance, in what direction they pass, and if more than one person passes during a predefined interval. You can also use it to estimate how many people are currently occupying an area, and the average visiting time.

The application runs embedded in the camera which means you don’t need a dedicated computer to run the application. AXIS People Counter is suitable for any indoor environment, like stores, libraries, or gyms.

How does estimating occupancy work?

You can use the application to estimate occupancy in areas with one or several entrances and exits. Each entrance and exit needs to be equipped with a network camera with AXIS People Counter installed. If there are several cameras, they communicate with each other over the network in a primary and secondary concept. The primary camera continuously fetches data from the secondary cameras and presents the data in the live view. Every fifteen minutes, the primary camera sends the statistical data to AXIS Store Data Manager. Consequently, the reports generated from AXIS Store Data Manager can present the data in a minimum of 15 minutes time interval.

AXIS Object Analytics is an analytic application that comes preinstalled on the camera. It detects objects that move in the scene and classifies them as, for example, humans or vehicles. You can set up the application to send alarms for different types of objects. To find out more about how the application works, see AXIS Object Analytics user manual.

AXIS Image Health Analytics is an AI-based application that can be used to detect image degradations or tampering attempts. The application analyzes and learns the behavior of the scene to detect blurriness or underexposure in the image, or to detect an obstructed or redirected view. You can set up the application to send events for any of these detections, and trigger actions through the camera’s event system or third-party software.

To find out more about how the application works, see AXIS Image Health Analytics user manual.

You can clean your device with lukewarm water.

1. Use a can of compressed air to remove dust and loose dirt from the device.

2. If necessary, clean the device with a soft microfiber cloth dampened with lukewarm water.

3. To avoid stains, dry the device with a clean, nonabrasive cloth.

This device supports microSD/microSDHC/microSDXC cards.

For SD card recommendations, see axis.com.

microSD, microSDHC, and microSDXC Logos are trademarks of SD-3C LLC. microSD, microSDHC, microSDXC are trademarks or registered trademarks of SD-3C, LLC in the United States, other countries or both.

• The control button is used for:

• Resetting the product to factory default settings. See Reset to factory default settings.

Use the intrusion alarm switch to get a notification when someone opens the device’s housing. Create a rule to make the device perform an action when the switch is activated. See Trigger a notification when the enclosure is opened.

RJ45 Ethernet connector with Power over Ethernet (PoE).

Use the I/O connector with external devices in combination with, for example, motion detection, event triggering, and alarm notifications. In addition to the 0 VDC reference point and power (12 V DC output), the I/O connector provides the interface to:

Digital input

For connecting devices that can toggle between an open and closed circuit, for example PIR sensors, door/window contacts, and glass break detectors.

Supervised input

Enables possibility to detect tampering on a digital input.

Digital output

For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, through an event or from the device’s web interface.

4-pin terminal block

Example

1. DC ground
2. DC output 12 V, max 25 mA
3. Supervised input
4. Digital output

To reset the product to the factory default settings:

1. Disconnect power from the product.

2. Press and hold the control button while reconnecting power. See Product overview.

3. Keep the control button pressed for 15–30 seconds until the status LED indicator flashes amber.

4. Release the control button. The process is complete when the status LED indicator turns green. If no DHCP server is available on the network, the device IP address will default to one of the following:

5. • Devices with AXIS OS 12.0 and later: Obtained from the link-local address subnet (169.254.0.0/16)

   • Devices with AXIS OS 11.11 and earlier: 192.168.0.90/24

6. Use the installation and management software tools to assign an IP address, set the password, and access the device.

   The installation and management software tools are available from the support pages on axis.com/support.

You can also reset parameters to factory default through the device’s web interface. Go to Maintenance > Factory default and click Default.

To reset the product to factory default settings:

1. Disconnect power from the product.

2. Change the position of the factory default switch. For more information on how to access the switch, see the Installation Guide.

3. Re-connect power to the product.

It is also possible to reset parameters to factory default via the web interface. Go to Setup > System Options > Maintenance and click Default.

Axis offers device software management according to either the active track or the long-term support (LTS) tracks. Being on the active track means continuously getting access to all the latest product features, while the LTS tracks provide a fixed platform with periodic releases focused mainly on bug fixes and security updates.

Using AXIS OS from the active track is recommended if you want to access the newest features, or if you use Axis end-to-end system offerings. The LTS tracks are recommended if you use third-party integrations, which are not continuously validated against the latest active track. With LTS, the products can maintain cybersecurity without introducing any significant functional changes or affecting any existing integrations. For more detailed information about Axis device software strategy, go to axis.com/support/device-software.

AXIS OS determines the functionality of our devices. When you troubleshoot a problem, we recommend that you to start by checking the current AXIS OS version. The latest version might contain a correction that fixes your particular problem.

To check the current AXIS OS version:

1. Go to the device’s web interface > Status.

2. Under Device info, see the AXIS OS version.

1. Download the AXIS OS file to your computer, available free of charge at axis.com/support/device-software.

2. Log in to the device as an administrator.

3. Go to Maintenance > AXIS OS upgrade and click Upgrade.

4. When the upgrade has finished, the product restarts automatically.

You can use AXIS Device Manager to upgrade multiple devices at the same time. Find out more at axis.com/products/axis-device-manager.

Problems upgrading AXIS OS

Problems setting the IP address

Problems accessing the device

Problems with streaming

Problems with MQTT

Problems with operating the device

If you can’t find what you’re looking for here, try the troubleshooting section at axis.com/support.

When you set up your system, it’s important to consider how different settings and situations affect performance. Some factors affect bandwidth (bitrate), others affect frame rate, and some affect both.

The most important factors to consider:

• High image resolution or lower compression levels result in images containing more data which in turn affects the bandwidth.

• Rotating the image in the GUI can increase the product's CPU load.

• Access by large numbers of Motion JPEG clients or unicast H.264/H.265/AV1 clients affects the bandwidth.

• Simultaneous viewing of different streams (resolution, compression) by different clients affects both frame rate and bandwidth.

  Use identical streams wherever possible to maintain a high frame rate. Stream profiles can be used to ensure that streams are identical.

• Accessing video streams with different codecs simultaneously affects both frame rate and bandwidth. For optimal performance, use streams with the same codec.

• Heavy usage of event settings affects the product’s CPU load which in turn affects the frame rate.

• Using HTTPS may reduce frame rate, in particular if streaming Motion JPEG.

• Heavy network utilization due to poor infrastructure affects the bandwidth.

• Viewing on poorly performing client computers lowers perceived performance and affects frame rate.

• Running multiple AXIS Camera Application Platform (ACAP) applications simultaneously may affect the frame rate and the general performance.

• How to assign an IP address and access your device

If you need more help, go to axis.com/support.