AXIS T6112 Mk II Audio and I/O Interface

When you connect your device to a supported Axis camera, settings for audio and I/O will appear on the camera's webpage.

You can manage all the settings described in this manual through the camera's webpage.

To learn more, check out our guide Get started with rules for events.

1. Go to System > Events and add a rule. The rule defines when the device will perform certain actions. You can set up rules as scheduled, recurring, or manually triggered.

2. Enter a Name.

3. Select the Condition that must be met to trigger the action. If you specify more than one condition for the rule, all of the conditions must be met to trigger the action.

4. Select which Action the device should perform when the conditions are met.

You have the option to connect the AXIS I/O Indication LED to your network camera. This LED can be configured to turn on whenever certain events occur in the camera. For example, to let people know that video recording is in progress.

Required hardware

• AXIS I/O Indication LED

• An Axis network video camera

• Note

  For instructions on how to connect the AXIS I/O Indication LED, see the installation guide provided with the product.

The following example shows how to configure a rule that turns on the AXIS I/O Indication LED to indicate that camera is recording.

1. Go to System > Accessories > I/O ports.

2. For the port that you connected the AXIS I/O Indication LED to, click to set the direction to Output, and click to set the normal state to Circuit open.

3. Go to System > Events.

4. Create a new rule.

5. Select the Condition that must be met to trigger the camera to start recording. It can, for example, be a time schedule or motion detection.

6. In the list of actions, select Record video. Select a storage space. Select a stream profile or create a new. Also set the Prebuffer and Postbuffer as required.

7. Save the rule.

8. Create a second rule and select the same Condition as in the first rule.

9. In the list of actions, select Toggle I/O while the rule is active, and then select the port the AXIS I/O Indication LED is connected to. Set the state to Active.

10. Save the rule.

• Other scenarios where AXIS I/O Indication LED can be used are for example:

• Configure the LED to turn on when the camera starts, to indicate the presence of the camera. Select System ready as a condition.

• Configure the LED to turn on when live stream is active to indicate that a person or a program is accessing a stream from the camera. Select Live stream accessed as a condition.

This example explains how to direct the camera and open a gate when someone wants to enter during daytime. This is done by connecting a PIR detector to the product’s input port and a switch relay to the product’s output port.

Required hardware

• Mounted PIR detector

• Switch relay connected to the gate lock, in this case the switch is normally closed (NC)

• Connecting wires

Physical connection

1. Connect the wires from the PIR detector to the input pin, see I/O connector.

2. Connect the wires from the switch to the output pin, see I/O connector

You need to connect the switch relay to the camera from the camera’s web interface. First, configure the I/O ports:

Set the PIR detector to an input port

1. Go to System > Accessories > I/O ports.

2. Click to set the direction to input for port 1.

3. Give the input module a descriptive name, for example “PIR detector”.

4. If you want to trigger an event whenever the PIR detector senses motion, click to set the normal state to circuit open.

Set the switch relay to an output port

1. Click to set the direction to output for port 2.

2. Give the output module a descriptive name, for example “Gate switch”.

3. If you want to open the gate whenever an event is triggered, click to set the normal state to circuit closed.

1. Go to System > Events and add a rule.

2. Type a name for the rule, for example “Open gate”.

3. In the list of conditions, select PIR detector.

4. In the list of actions, select Toggle I/O once.

5. In the list of ports, select Gate switch.

6. Set state to Active.

7. Set the duration.

8. Click Save.

This example explains how to send an email when the input signal is cut or short-circuited. For more information about the I/O connector, see I/O connector.

1. Go to System > Accessories and turn on Supervised for the relevant port.

1. Add an email recipient:

2. Go to System > Events > Recipients and add a recipient.

3. Type a name for the recipient.

4. Select Email.

5. Type an email address to send the email to.

6. The camera doesn’t have it’s own email server, so it has to log into another email server to send mails. Fill in the rest of the information according to your email provider.

7. To send a test email, click Test.

8. Click Save.

1. Create a rule:

2. Go to System > Events > Rules and add a rule.

3. Type a name for the rule.

4. In the list of conditions, under I/O, select Supervised input tampering is active.

5. Select the relevant port.

6. In the list of actions, under Notifications, select Send notification to email and then select the recipient from the list.

7. Type a subject and a message for the email.

8. Click Save.

1. Turn on audio:

2. Go to Video > Stream > Audio and include audio.

3. If the device has more than one input source, select the correct one in Source.

4. Go to Audio > Device settings and turn on the correct input source.

5. If you make any changes to the input source, click Apply changes.

6. Edit the stream profile that is used for the recording:

7. Go to System > Stream profiles and select the stream profile.

8. Select Include audio and turn it on.

9. Click Save.

This use case explains how to make it possible to communicate with audio through the product.

1. Connect a microphone and a speaker to the product:

2. Connect a microphone to the Audio in connector.

3. Connect a speaker to the Audio out connector.

1. Allow two-way audio in the camera's web page:

2. Go to Video > Stream > Audio and include audio.

3. Go to Audio > Device settings and make sure audio is allowed.

4. Turn on the correct input source.

5. If you make any changes to the input source, click Apply changes.

6. Go to System > Plain config.

7. Set Select group to Audio.

8. Make sure Duplex mode is set to Full duplex

Input: RJ45 Ethernet connector with Power over Ethernet (PoE).

Output: RJ45 Ethernet connector with Power over Ethernet (PoE).

• Audio in – 3.5 mm input for a digital microphone, an analog mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

• Audio out – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out.

Audio input

Audio output

Use the I/O connector with external devices in combination with, for example, motion detection, event triggering, and alarm notifications. In addition to the 0 V DC reference point and power (12 V DC output), the I/O connector provides the interface to:

Digital input

For connecting devices that can toggle between an open and closed circuit, for example PIR sensors, door/window contacts, and glass break detectors.

Supervised input

Enables possibility to detect tampering on a digital input.

Digital output

For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, through an event or from the device’s web interface.

4-pin terminal block

Example

1. DC ground
2. DC output 12 V, max 50 mA
3. I/O configured as supervised input
4. I/O configured as output

If you can’t find what you’re looking for here, try the troubleshooting section at axis.com/support

If you need more help, go to axis.com/support.